{"product_id":"bently-nevada-330709-000-080-10-01-00-3300-xl-11-mm-proximity-probe-vibration-sensor","title":"Bently Nevada 330709-000-080-10-01-00 3300 XL 11 mm Proximity Probe – Vibration Sensor","description":"\u003ch2\u003eProduct Introduction\u003c\/h2\u003e\u003cp\u003eWhen cross-talk and temperature extremes threaten vibration monitoring accuracy, the \u003cstrong\u003eBently Nevada 330709-000-080-10-01-00\u003c\/strong\u003e 3300 XL 11 mm Proximity Probe provides reliable performance. This non-contact sensor, built with a polyphenylene sulfide (PPS) tip and AISI 304 stainless steel case, delivers precise shaft displacement measurements in critical rotating machinery. With a DC resistance of 5.9 ± 0.5 ohms and a 75 ohm triaxial FEP insulated cable, it ensures signal integrity even in harsh environments.\u003c\/p\u003e\u003ch2\u003eTechnical Specifications Breakdown\u003c\/h2\u003e\u003cp\u003eKey parameters of the \u003cstrong\u003eBently Nevada 330709-000-080-10-01-00\u003c\/strong\u003e include:\u003c\/p\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eParameter\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe DC Resistance (RPROBE)\u003c\/td\u003e\n\u003ctd\u003e5.9 ± 0.5 Ω (1.0 m length)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Case Torque (M16x1.5)\u003c\/td\u003e\n\u003ctd\u003eMax 63.3 N·m, Recommended 21.1 N·m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Torque\u003c\/td\u003e\n\u003ctd\u003eFinger tight; Max 0.565 N·m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum Bend Radius\u003c\/td\u003e\n\u003ctd\u003e25.4 mm (1.0 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Temperature Range\u003c\/td\u003e\n\u003ctd\u003e-52°C to +177°C (-62°F to +351°F)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Specification\u003c\/td\u003e\n\u003ctd\u003e75 Ω triaxial, FEP insulated\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Tip Material\u003c\/td\u003e\n\u003ctd\u003ePolyphenylene sulfide (PPS)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Case Material\u003c\/td\u003e\n\u003ctd\u003eAISI 304 stainless steel\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003cp\u003eThese specs ensure the probe withstands high torque during installation and maintains linearity across a wide temperature range.\u003c\/p\u003e\u003ch2\u003eIndustry Applications\u003c\/h2\u003e\u003cp\u003eThe \u003cstrong\u003eBently Nevada 330709-000-080-10-01-00\u003c\/strong\u003e excels in turbine, compressor, and pump vibration monitoring. For example, in a steam turbine, the probe detects shaft radial vibration, preventing costly unplanned outages. Its cross-talk limitation (recommended minimum target diameter 30.5 mm) allows reliable operation where multiple probes share a common target. The probe's operating temperature range suits both indoor and outdoor installations in power generation and petrochemical plants.\u003c\/p\u003e\u003ch2\u003eInstallation \u0026amp; Setup Guidance\u003c\/h2\u003e\u003cp\u003eMount the \u003cstrong\u003eBently Nevada 330709-000-080-10-01-00\u003c\/strong\u003e using the M16x1.5 thread with a maximum engagement length of 24 mm. Apply the recommended torque of 21.1 N·m (187 in·lb) to secure the case without over-tightening. For the miniature coaxial ClickLoc connector, tighten only finger tight (max 0.565 N·m). Maintain a minimum bend radius of 25.4 mm for the cable to prevent internal damage. Avoid exposing the probe to temperatures below -34°C (-30°F) as this may cause premature pressure seal failure.\u003c\/p\u003e\u003ch2\u003eMaintenance \u0026amp; Reliability\u003c\/h2\u003e\u003cp\u003eRegularly inspect the cable and connector for wear, especially near bend points. The \u003cstrong\u003eBently Nevada 330709-000-080-10-01-00\u003c\/strong\u003e requires no periodic calibration if installed correctly, reducing total cost of ownership. Store the probe in its original packaging at temperatures between -55°C and +177°C. For hazardous locations, note the temperature schedules (T1 to T5 for EPL Ga\/Gc and Dc) to ensure compliance. This probe's robust construction minimizes downtime, aligning with a failure-mode prevention approach.\u003c\/p\u003e\u003ch2\u003eTroubleshooting \u0026amp; Common Issues\u003c\/h2\u003e\u003cp\u003eCommon problems with proximity probes include cross-talk and signal drift. The \u003cstrong\u003eBently Nevada 330709-000-080-10-01-00\u003c\/strong\u003e addresses cross-talk by requiring a minimum flat target diameter of 30.5 mm and a minimum shaft diameter of 152 mm. To avoid temperature-induced errors, operate within the -52°C to +177°C range. If the probe resistance deviates from 5.9 ± 0.5 ohms, check cable integrity and connector tightness. For persistent noise, verify the cable is kept away from high-voltage lines. These measures ensure long-term measurement accuracy.\u003c\/p\u003e\u003cp\u003eFor further assistance, contact UBEST Automation (available at \u003ca href=\"https:\/\/ubest101.myshopify.com\"\u003eubest101\u003c\/a\u003e) for application support and compatible accessories.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default","offer_id":44404367425635,"sku":"330709-000-080-10-01-00","price":230.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0678\/8635\/0435\/files\/330709_20_281_29_667eefa5-d394-4acb-b774-fd323ae87449.jpg?v=1785134495","url":"https:\/\/www.plcsourcepro.com\/products\/bently-nevada-330709-000-080-10-01-00-3300-xl-11-mm-proximity-probe-vibration-sensor","provider":"PLC Source PRO","version":"1.0","type":"link"}